Ametek DM-T-150 Calibration Instruments
  • Ametek DM-T-150 Calibration Instruments

Ametek DM-T-150


Type T Hydraulic Deadweight Tester, Distilled Water/Alcohol Medium; 10-15000 psi



The Ametek DMT150 Type T Hydraulic Deadweight Tester, Distilled Water/Alcohol Medium; 10-15000 psi is a dead weight tester that offers laboratory accuracy in an instrument designed to withstand an industrial environment or daily stresses of a manufacturing environment. Each tester features a re-entrant type measuring piston and cylinder assembly. This design reduces the rate of fluid leakage and increases float time, helping to maintain accuracy as test pressures increase. This model offers a range up to 1,000 bar (15,000 psi). This robust tester has been engineered to withstand the stresses of daily operation in a manufacturing environment and still maintain its accuracy and repeatability. The Type T is constructed of 300 series stainless steel and Monel and is supplied with Buna N O-rings as a standard unit. This deadweight can use a water/alcohol mix or hydraulic oils for the pressure medium. The DM-T-150 model offers accuracy of ±0.015% of reading. The accuracy stated is the over-all accuracy of the tester. The accuracy takes into account linearity, hysteresis, and repeatability. It would also account for intrinsic corrections. Site corrections are the user's responsibility and the unit will not perform as specified without them. The testers are manufactured to either International Standard Gravity of 9.80665 m/s2 or to a user specified local gravity.

Re-entrant piston/cylinders

The Type T deadweight employs a re-entrant type piston/cylinder assembly. This design applies test fluid to the outside and inside of the cylinder. Unlike a simple piston/cylinder, this configuration reduces clearance between the piston and cylinder as pressure increases. This reduces the rate of fluid leakage and increases float time, offers the technician more time for testing, and reduces the amount of pumping necessary to sustain the fluid loss.

Overhung weight carriers

Another feature of Type T deadweight tester is the way that the weights are positioned on the carrier. M&G utilizes an overhung weight carrier design. This design employs a tube carrier that is positioned over the column and onto the piston driver. The center of gravity for the stack of weights is lowered, reducing side thrust and friction; which lengthens the life of the piston/cylinder assembly. This also improves measurement accuracy.

Protected piston/cylinder

The piston and cylinder assembly are enclosed in the column of the tester. The weight carrier floats on the piston driver preventing damage to the piston/cylinder assembly. Additionally, the piston/cylinder assembly is engineered with positive over-pressure protection by restricting vertical movement. This protects the assembly from damage in the event of weight removal under pressure.

Dual volume pump

The Type T pump offers a dual volume pumping feature that allows for large volume of fluid to be added at low pressures to fill the system and increase pressure rapidly. Once the system is filled, output volume can be switched to a smaller volume. This eases pumping and also provides for finer control in higher pressure ranges. The reservoir is kept at atmospheric pressure meaning that the tester can also be refilled during a calibration run.

Easy Leveling

Ametek floating ball testers incorporate a bulls-eye level for reference when preparing the unit for use. The tester also employs a 3-leg leveling system which is more convenient and is superior to a 4-leg system.

Product Features:

  • Type: Hydraulic, piston gauge
  • Pressure Range: 100 to 10,000 kPa (10 to 15,000 psi)
  • Dual Range:
    • 10 to 1,500: Increments: 5, Piston: 0.10 in2
    • 100 to 15,000: Increments: 50, Piston: 0.01 in2
  • Standard pressure accuracy: ± 0.015% of reading
  • Repeatability: ±0.005% of Indicated reading
  • Available units: psi, kg/cm2, bar, kPa
  • Pressure connection: 1/4 in. and 1/2 in. NPT F
  • Single column, dual piston
  • Robust construction allows for repeated daily use
  • Complete tester with tools, cases, and fittings
  • Traceable certification supplied with each tester
  • Overhung weight carrier reduces side thrust and friction
  • Over-pressure protection prevents piston damage
  • 3- leg design with bulls-eye leveling system
Product Details
6 other products in the same category:

Reference: FL22717649F7

Brand: Fluke

Fluke 705

Loop Calibrator, .02% Accuracy

Price $388
In stock

Reference: EX84378320E4

Brand: Extech

Extech 407766-NIST

Sound Level Calibrator with 94 dB or 114 dB Output with NIST Calibration

Price $265
In stock

Reference: AD78120380AA

Brand: Additel

Additel ADT223A

Multifunction Process Calibrator with HART Communication

Price $3,661
In stock

Reference: FL58833105FC

Brand: Fluke

Fluke Calibration 7109A-P-156

Portable Temperature Calibration Bath with Process Electronics, -25 °C to 140 °C (-13 °F to 284 °F), 115VAC

Price $6,708
In stock

Follow us on Facebook